avoid_crossing_perimeters = 1
bed_shape = rectangular
bed_size = 180,180
bed_temperature = 60
bottom_clip_amount = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
build_height = 180
cancel_gcode = M104 S0\nM140 S0\n\nM4
center_part_on_bed = 1
complete_objects = 0
connect_gcode = 
cool_extruder_lift = 0
print_leveling_solution = 3 Point Plane
print_leveling_method = Manual
print_leveling_required_to_print = 0
manual_probe_paper_width = .1
cooling = 1
create_raft = 0
default_acceleration = 0
disable_fan_first_layers = 2
end_gcode = M104 S0 ; turn off temperature\nM140 S0\nG91\nG1 E-5.0 F12000\nG90\nG28 X\nM84     ; disable motors
external_perimeter_speed = 35
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_count = 1
extruder_offset = 0x0,0x0,0x0,0x0
extruder_wipe_temperature = 0
extruders_share_temperature = 0
extrusion_axis = E
extrusion_multiplier = 0.96
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 0
fill_density = 20%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 75
first_layer_extrusion_width = 0
first_layer_height = 0.3
first_layer_speed = 12
first_layer_temperature = 205
g0 = 0
gap_fill_speed = 20
gcode_arcs = 1
gcode_comments = 0
gcode_flavor = reprap
gcode_output_type = REPRAP
has_fan = 1
has_hardware_leveling = 0
has_heated_bed = 1
has_power_control = 0
has_sd_card_reader = 1
show_reset_connection = 0
heat_extruder_before_homing = 0
include_firmware_updater = None
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap_perimeter = 0.12
infill_speed = 40
infill_type = HEXAGON
layer_gcode = 
layer_height = 0.25
layer_to_pause = 
max_fan_speed = 100
min_extrusion_before_retract = 1.5
min_fan_speed = 60
min_print_speed = 5
min_skirt_length = 2
notes = 
nozzle_diameter = 0.4
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
pause_gcode = G91\nG1 Z10 E-10 F12000\nG90
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
external_perimeter_extrusion_width = 0
perimeter_speed = 40
perimeters = 2mm
post_process = 
print_center = 90,90
raft_air_gap = 0
raft_extruder = 0
raft_extra_distance_around_part = 5
raft_fan_speed_percent = 100
raft_layers = 0
raft_print_speed = 100%
bed_remove_part_temperature = 0
randomize_start = 0
repair_outlines_extensive_stitching = 0
repair_outlines_keep_open = 0
resolution = 0
resume_gcode = G91\nG1 Z-10 E10.8 F12000\nG90
retract_before_travel = 5
retract_layer_change = 1
retract_length = 3
retract_length_tool_change = 10
retract_lift = 0
retract_restart_extra = 0.1
retract_restart_extra_toolchange = 0
retract_when_changing_islands = 1
retract_speed = 110
skirt_distance = 0
skirt_height = 1
skirts = 25
slowdown_below_layer_time = 40
small_perimeter_speed = 30
solid_fill_pattern = rectilinear
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60
solid_shell = 0
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = M104 S200\nM190 S60\nM109 S200\nG28\nG1 Y90
start_perimeters_at_concave_points = 0
start_perimeters_at_non_overhang = 1
support_air_gap = .3
support_material = 1
support_material_angle = 45
support_material_percent = 4
support_material_create_internal_support = 1
support_material_create_perimeter = 1
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_infill_angle = 30
support_material_interface_extruder = 1
support_material_interface_layers = .9mm
support_material_interface_spacing = 0
support_material_pattern = honeycomb
support_material_spacing = 3
support_material_speed = 40
support_material_threshold = 20
support_material_xy_distance = 0.7
support_material_z_distance = 0.15
support_material_z_gap_layers = .3mm
support_type = GRID
temperature = 200
thin_walls = 1
threads = 4
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 300
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
wipe_shield_distance = 0
wipe_tower_size = 0
z_can_be_negative = 0
z_offset = 0